Sale, Tridium LED Lower Fog & Turn Signal Light Kit

[RickW]

We have the Tridium LED Lower Fog & Turn Signal Light Kits on sale right now for $243.95.
These are the updated and a great addition to your F6B or Goldwing.
Click on this link.
http://store.valueaccessories.net/Tr...KitGL1800.aspx

The pictures will be on our product page.

[BuzzzPhotos]

Thanks! Been wanting them for a while. They're on the way.

[Talldude]

Hey Rick are theyl plug and play for the f6b or do you nned to cut wires?

thanks

[RickW]

Hey Rick are they plug and play for the f6b or do you need to cut wires?

thanks

Just for questions like this I do have a link on the product page to the instructions.
http://www.bigbikeparts.com/catalog/...915_52-916.pdf

You do not have to cut wires on the F6B.

http://store.valueaccessories.net/Tr...KitGL1800.aspx

[Talldude]

Just for questions like this I do have a link on the product page to the instructions.
http://www.bigbikeparts.com/catalog/...915_52-916.pdf

You do not have to cut wires on the F6B.

http://store.valueaccessories.net/Tr...KitGL1800.aspx

thanks

[Ray H]

Placed my order last night and they were shipped this morning. Thanks, Rick.

[tpwood]

Hey Rick are theyl plug and play for the f6b or do you nned to cut wires?

thanks

You do have to cut wires, if you look at the directions near the bottom of the instructions, the F6B requires cutting the end connectors off the splicing them to the factory wiring. Just installed mine last week.

**NOTE: FOR 2001-2005 GL1800, F6B AND VALKYRIE MODELS YOU WILL NEED TO CUT OFF THE END WITH TWO CONNECTORS AND SPLICE THE RED WIRES FOR EACH
TURN SIGNAL, THE BLUE WIRES FOR EACH RUNNING LIGHT AND THE BLACK WIRES ARE FOR GROUNDS

So the Red wires splice to the solid color wires (Orange for left and Blue for right), the white stripe wires are the running light (blue) and the ground wire, green goes to the black wires.

[RickW]

You do have to cut wires, if you look at the directions near the bottom of the instructions, the F6B requires cutting the end connectors off the splicing them to the factory wiring. Just installed mine last week.

**NOTE: FOR 2001-2005 GL1800, F6B AND VALKYRIE MODELS YOU WILL NEED TO CUT OFF THE END WITH TWO CONNECTORS AND SPLICE THE RED WIRES FOR EACH
TURN SIGNAL, THE BLUE WIRES FOR EACH RUNNING LIGHT AND THE BLACK WIRES ARE FOR GROUNDS

So the Red wires splice to the solid color wires (Orange for left and Blue for right), the white stripe wires are the running light (blue) and the ground wire, green goes to the black wires.

I obviously was wrong, the new version comes with plugs for the newer GL1800 which has different connectors then the F6B. So you just cut the connector off that comes on it and splice into the existing wires.
We have had very good feedback on these.

[Colorado]

Rick,

Any chance these might go on sale again? Also, any plans to put the sequential turn signals on sale?

David

[Brasco]

Sent Rick a pm a few days ago about this very thing (to cut wire or not) and he was great -- cleared things up for me quickly. Thanks Rick!

But now I have another question I'm hoping someone out there knows the answer to. The driving light/turn signal harness has two connectors on the end that goes inside each mirror housing. Does anyone know where to cut these off and how to tap into the pre-existing connector inside each mirror. Guessing you need to use a butt end heat shrink style connector for each of the three wires but not sure. Honda dealership could offer no useful advice whatsoever.

Thanks!