PDA

View Full Version : Billet Badges in reflector locations



Hambly434
05-08-2013, 12:30 PM
I only have the fronts figured out so far.
Unbolt the reflector and bolt the badge in its place.
$35 a pair. For brushed alum. That would cover shipping and SS stud. Should use stock nut and washer.
Have material on order to make a run of them.
Will have a quote from anodize company by the end of the week.
They will anodized black then engraved.
Just wanting to get a idea if anyone would be interested
Before doing the rear ones also was thinking of a license plate bracket.

Cool Hand Luke
05-08-2013, 12:57 PM
I want a pair. Would black anodized mean the plate is black while letters will be in aluminum color? If so, it may be even nicer. I think it would look great as a pair front and back. Maybe do a cover for replacing a small red reflector in back above license plate. Thanks.

Hambly434
05-08-2013, 02:46 PM
Correct the engraving will be an aluminum color. Don't know cost of anodizing yet. As soon as I do I'll let you know. Just looked at the one below the license plate light last night but haven't unbolted yet. Bike is at shop for first checkup. Going to get it now.

BLACKBETTY12
05-08-2013, 05:37 PM
I want a pair. Would black anodized mean the plate is black while letters will be in aluminum color? If so, it may be even nicer. I think it would look great as a pair front and back. Maybe do a cover for replacing a small red reflector in back above license plate. Thanks.

Sounds good!

BACA
05-08-2013, 06:07 PM
I'm interested......I'd like the black with aluminum engraving if you do em.

Cool Hand Luke
05-08-2013, 07:41 PM
Looks like I'm in for black anodized engraved pair. Also would like to get the rear pair, as well as rear reflector cover if you end up making it, so five total for me :-)

Hambly434
05-12-2013, 01:14 PM
Just a update. Front fenders and rear under the license plate light are all the same. I'll work on the bags this week.
The plater has a 100 part minimum. So, sorry that's a no go at the present time.
I only bought 1 12' bar of stock to start with.

Cool Hand Luke
05-12-2013, 02:33 PM
I definitely like your new F6B engraving better! I am interesting to see what the saddlebag reflectors will look like.

Hambly434
05-12-2013, 02:52 PM
Thanks. The first set I did last week I just used the font available in the software. I had to draw this from scratch tried to get it close without being exact. I'm not quite sure how the trademark laws work but I don't need any problems.
I did pry off a bag reflector they are held on with tape. I'll try to get one done this week. They are smaller plus have a angle on the back also a orientation groove. The first set will be a pain but after that should be good.

Hambly434
05-13-2013, 06:57 PM
Here's some more test parts.
Pm if your interested

Hambly434
06-04-2013, 09:36 PM
Have black and brushed available.

Kawi69
08-26-2013, 11:54 AM
Hey Hambly 434, I'd like a set of front & rear "Black Anodized" F6B. How much for the License Plate frame?

Hambly434
08-26-2013, 03:32 PM
No problem have them ready to go.
$75.00 for lic. plate frame.
Sent you a PM for shipping info.

06Blackpearl
12-28-2015, 07:32 PM
These still available??

JackB
12-29-2015, 07:11 PM
These still available??

He stopped making badges about a year ago, he got some kind of big job so he had no time for the badges.

114th COBRA
12-30-2015, 02:44 PM
Dog-gonnit.:icon_frown: Sure like that License Plate Frame.

M61A1MECH
12-30-2015, 08:00 PM
I got some of the last fairing badges that Neil made, hope he starts making them again.
363636373638

06Blackpearl
12-30-2015, 10:28 PM
He stopped making badges about a year ago, he got some kind of big job so he had no time for the badges.

Thanks guess I'll make my own ...