The pipes sound better today than yesterday, it's the gift that keeps on giving...aint that true Barry
https://youtu.be/Fh_26t7W8yA
Printable View
The pipes sound better today than yesterday, it's the gift that keeps on giving...aint that true Barry
https://youtu.be/Fh_26t7W8yA
Love the sound and craftsmanship on those puppies. The Rush I ordered were out of stock. I cancelled and went with the TBRs also. I had been on the fence for months, your videos helped me a lot. thanks!
are you having problems posting pics also?
It's all TBR on this one
https://youtu.be/Q4pMz6OFAbE
Mike!
We need a "drive by" video with sound of those TBR's.... coming and going. :yes:
https://www.youtube.com/watch?v=HepKef_BalA
This is probably the best camera/sound perspective I've seen in any video, well done Tax! If I hadn't bought my TBR's last year and was still on the fence, this would've clinched it for me no question. Now I find myself hoping my chrome tbr's sound that good.
https://img.memecdn.com/neener-neener_o_918187.jpg
:stirthepot:
go Barry:clap2:
A lady, a motorcycle, a little Barry ==== Wonderful things can happen.
What a fine looking set of pipes! How bad is the "drone" w/ those?
Hey Taxfree4! I just installed the TBRs on my F6B. I notices from your video yours has a very nice crackle & pop sound either at cruise or deceleration I believe. I fired mine up just briefly and they had a very nice rumble but no pop or crackle. Do you think that is your torque loops or maybe my bike just was not warmed up enough.
Also, are there any videos or posts out there regarding aligning the angled slip tubes as well as aligning those dang heat shields. Im having a hell of a time getting it right and have given up for the day. There seem to be a several millimetre gap between the heat shield & the pipes on mine. I'm wondering if it is because I haven't aligned them right but can't seem to get it any better. Not sure if I'm doing something wrong with the alignment.
Thanks.
Just fired it up again. One clamp not tightened yet, bike is in the garage, and there is a terrible loud drone sound at idle. Oh oh! Suggestion? Input?
I can tell you first hand, the drone was horrendous for me. The torque loops totally fixed it, and made it sound better also. One tip when installing the slip-ons or loops. Test fit your heat shields and lowers before you tighten all your clamps and hangers.... I did not, and I had to adjust everything to fit.
Correct, I installed the hanger bolt and slipped the nut on a couple of turns. BTW, if it's only a millimeter or 2 just loosen up the CAT/header side and slip it back on the exhaust/CAT end and re-tighten. If you don't want to do that if you have a DREMEL ream out the hole on the flange for the hanger bolt to move forward the mil. or 2 you need.
Ok. All installed nice & symmetrical. Definite drone. I guess I now need torque loops. Saw your video taxfree4. Looks like a big job.
I just did the Torq Loopz instal this weekend. The actual taking off of the exhaust system and making the cuts is really easy. Its the redoing all of the work you did that is the PITA. Although at this point, the off and on of the front cowling, lowers, and mufflers goes really fast. It really is less complicated than it seems. Makes ALL the difference in the world though.
Thanks for the replies. Outside of the drone elimination, what else did you notice?
Definite notice in throttle response and she moves and sounds so much better. It just breathes so well and the sound will be deep and throaty.
If you can use a hacksaw you can do this, other than that you're just aligning and rehanging the headers and mufflers. I have the color instructions on a PDF file and if you watch the video it'll be a snap.
Fast forward to :50 in the below video.... sorry Mike.. couldn't help it.... :icon_mrgreen:
https://www.youtube.com/watch?v=0VSO-88E8qo
I should be getting the torque loops soon.
Reviewed your video Tax. Looks straight forward.
How do I know how far back to cut the cats off the headers. Is that in the instructions?
Thought I'd ask to get some responses before they get here.
I believe it is in the 1 3/4" range. Taxfree will probably chime in when he gets back from a long ride today enjoying his TBR-Torq Looped exhaust. Here's a vid to watch on them..........
https://www.youtube.com/watch?v=unAc-iOYM9A
The instructions say "1 3/4 to 1 5/8". the give you a little bit of wiggle room.
how do i slide the tbr swivel tube over the torque loops flange? the slip tube went on easy over the original header but now with the loops installed the swivel tubes seem too tight and unadjustable.
Also, i have loosely installed the tbr pipe but the heat shield doesn't align with the torque loop slotted hole.
On my way to a muffler shop. The slip tubes are simply too tight there for non-adjustable. Hoping to have them enlarged slightly to make the adjustments easier. I tried filing the insides, helped a little but not enough. Anyone else have to do the same?
There should not be a problem, you did apply the grease pac that came with it, one side for me was a little stubborn but if you have those rubber banded pipe wrenches they'll work. Also before you tighten up go to the back and make sure the pipes are equidistant from the sides of the back panel.
https://s1.postimg.org/kpvu38tuz/image.jpg
Thanks for responding. No I'm not using the colors. Cal thanks for responding. No I'm not using the okd collars. The problem I'm having is sliding the swivel tubes over the torque loop flange. Requires a lot of force to get on and then doesn't twist to adjust. Muffler shop suggests slightly grinding the inside of the swivel tube. Lube didn't make a difference. Grinding with the file helped but not enough.
Also, the grease pack is all used up.
Been using teflon lube.
I first isnstslled just the TBR mufflers. Challenging time aligning everything but figured it out. The F6B sounded much better.
The Sound was nice but terrible drone between 2-3,000 rpm. Definitely not enjoyable. Could not live with this.
Following weekend dropped the pipes and installed the torque loops. I had to grind the inside of one side of the muffler swivel tube with a dremmmel tool & I had to buy more antiseize to lube the tubes.
After several more hours, everything came together and aligned perfectly although at times I did have my doubts.
I took it for a test drive last night & I'll tell you if you want the bike a little louder, just do it & go for the loops right from the start.
The loops make the bike FLY!!!!!!!!
Throttle response is extremely more responsive & crisp with the loops. Much more torque. The bike moves much much faster through the gears. The TBR mufflers make the best sound in my opinion.
I went with the chrome although originally I felt I really wanted to keep the blacked out look but since my bike is black & red and I couldn't find any pics where the bike looked good with black pipes so I went with chrome. Obviously it is a personal choice. The chrome and the red breaks it up nicely and makes the bike pop! Everyone agrees.
The loops make the sound crisper, much more aggressive, throatier, crisper & gives a nice high performance sound that the mufflers alone did not give. The sound with these pipes together with the loops is obviously louder than stock but not offensive.
Also,
I can assure you that loud pipes can save lives.
Story;
Several years back when I had my VTX with Vance & Hines pipes I was riding to the cottage together with my wife & kids in the car while I ride the bike alongside.
We were on multi lane 400 highway northbound. I was coming up from behind on our families car in the lane beside them and unknown to me my wife was about to make a lane change but she stopped herself last second from changing lanes because she heard the pipes.
I noticed NOTHING! Upon arrival at the cottage my wife said thank god you installed those pipes or I would have hit you. My wife is a great driver with zero tickets and accidents. Food for thought..
Congratulations, welcome to the family the TBR and Torq Loopz are like a match made in heaven.
The Loops sound good with Rush mufflers and 2.5" baffles too. https://www.youtube.com/watch?v=2lX5vyNt8ak
Not my bike but have the Rush mufflers with 2.5 baffles. Will be adding Torque Loops sometime this year.