Shinhopples Shingrips +50

I should've purchased these straight out of the gate. Thanks to those on the forum who recommended them. It's honestly surprising how much these inexpensive foam grip covers improve the ride. If I had to quantify, I'd say for me, personally, there's probably a 50% reduction in wrist and arm fatigue compared to stock. Wow. I still think the suspension needs some attention to make it more absorbent, but I'm frankly astonished at how well these work. Thanks again.

Jason

https://www.shop.shinhopples.com/pro...categoryId=103

Owners Meesh and Bulldawg are great folks.

I've picked 'em up on ebay, under 10 bucks delivered

Will they transmit the heat from the OEM grips?

Quote:

---

Originally Posted by willtill

Will they transmit the heat from the OEM grips?

---

Yes, Willtill, but the effect is diminished. As a subjective measure--With the stock grips, I only had to turn the heat on high for 5-10 minutes before they were way too hot for me and I turned them down two or three clicks. With the shingrips on, they stay on full blast and still only feel somewhat warm. They've gone from easily keeping my hands toasty warm, to kind-of fending off the cold. It's an unfortunate trade-off. However, I'm willing to accept it because of the surprising increase in ride comfort.

Jason

Thanks Jason

You're welcome, Willtill. If I remember, you live in a much colder climate than me. If you get these and install, be sure and report back what you think. Your tolerance for cold is likely MUCH greater than mine so it will be interesting to hear.

Jason

I have these

http://www.cyclemax.com/inc/sdetail/...s/318814/15395

They transfer the heat from the grips well. They do take a little longer (1-2 min?) to heat up but once warm I keep them at the same level as before. I have about 12k miles with them so far and they are ready to be replaced.

Quote:

---

Originally Posted by P.Sutton

I have these

http://www.cyclemax.com/inc/sdetail/...s/318814/15395

They transfer the heat from the grips well. They do take a little longer (1-2 min?) to heat up but once warm I keep them at the same level as before. I have about 12k miles with them so far and they are ready to be replaced.

---

I prefer these (or Grip Puppies) as well. Transfer heat well and make a world of difference for a comfortable grip. Have them on 3 bikes and they last me 2-3 years. Tip for installation - put a towel or paper towel under the grip area to absorb overspray and then spray the existing grip and the inside of the foam grip liberally with non-aerosol (like a pump bottle) hair spray. They will just slip on. Squeeze the grip with the towel to absorb excess hair spray and let them dry for 20-30 minutes. If you don't have any spray, you can pick up a travel size spray bottle of TREsemme' hair spray (or something similar) for about $1.50 at Walmart or Target or similar stores.

If you have an air compressor available, start one end of the foam grip on the bars, place an air nozzle between the grip and the foam grip and apply air while pulling the grip on

Should take about 2 mins to install both sides, removal is much faster


I also have the Shinhopples, made a huge difference in comfort
https://www.shop.shinhopples.com/pro...categoryId=103

I have not noticed any difference in temperature with the heated grips

3 years/10,000 miles and the grips look brand new

I don't have heated grips but I'm trying out the Beemer Buddies grips this season.

Just slapped a pair on to try out on my 2000 mile trip next week.

I put Grip Puppies on last May, a couple weeks after I got the bike. My hands would get numb on long trips before I installed them. Haven't had numb hands since I put them on, wouldn't be without them now. No difference with heated grips that I can feel. Used the air compressor method to install, took about 2 min per side. (Tip) Put tape on the bar ends so you don't scratch them with the air nozzle.

I just ordered a fresh set of the shingrips, to replace the 2 year old ones I have. This will be my 3rd set.

I used a very small amount of dish soap on the inside of the foam grim to help them slide on. Not much at all is needed to get them to work their way onto the grip.