Which Bluetooth option the best?

[Macs_F6B]

So which is better blutooth solution:
A) https://www.youtube.com/watch?v=CAh5tGnJXDI
35$: https://electricalconnection.com/ind...bluetooth-aux/
Would also add I think this: https://electricalconnection.com/ind...audio-devices/
$25
Total $60
For above option i'm not sure its going to be loud enough based on what they guy in option B below says.....

Is this one going to do what this guy says here:
B) https://www.youtube.com/watch?v=dTlof-fr1w8
4 items total cost of: $60 :

• bluetooth adapter
• AMP
• ground loop noise isolator
• Maxboost car charger

For above option there is no way to also plug in your phone to usb because the amp and bluetooth device take both ports. Plus all that stuff will make my glove box kinda useless for stuff'''???


ALSO.. If you run either one of these what do you do if you want to press your AUX button and have the music stored on your USB drive attached in the left saddle bag to work?

Thanks for your advice in advance!

-Mac

[dustytrader]

Interesting videos. I'll be following to see which way is best for users on this forum before I buy one.

[SeaSteve]

To be clear...Both options give you a Bluetooth "INPUT" into the Goldwings existing audio system and speakers using the AUX 3.5 audio connector in the glovebox.

The "Block Diagram" description is...A Bluetooth enabled phone will send an audio stream to the Bluetooth enabled receiver in both options A & B. The Bluetooth receiver then sends the audio through the connected AUX 3.5 audio connector to the Goldwing audio system to be played through the speakers or connected headset.

So which is better blutooth solution:
A)... For above option i'm not sure its going to be loud enough based on what they guy in option B below says.....

I'm gonna say option a will be the same or lower in volume than just plugging your phone in on the 3.5 AUX plug. The Electrical Connection Bluetooth Receiver shouldn't amplify, just create a wireless Bluetooth connection on the AUX 3.5 audio input.

The Neoteck will amplify the audio signal coming out of the Bluetooth receiver, BEFORE the audio is sent to the AUX 3.5 audio connector, then on the Goldwing audio system.

Is this one going to do what this guy says here:
B)... For above option there is no way to also plug in your phone to usb because the amp and bluetooth device take both ports. Plus all that stuff will make my glove box kinda useless for stuff'''???

You could just COMBINE both A & B options into one and test it in steps. The USB Bluetooth adapter in option B "COULD" be replaced by the Electrical Connection Bluetooth Receiver, which allows you to easily move it BELOW the left side pocket and opens up a USB power connector. Get the Electrical Connection Bluetooth Receiver to start with and see how loud it is. Then purchase the Neoteck AMP if you need more volume. My electronic experience tells me the AMP may overdrive the aux 3.5 input and be more of a problem in the long run. I Do recommend leaving the AMP accessible in the left pocket so you can adjust the Volume knob if your phones MP3 streaming is louder than Internet radio streaming.

ALSO.. If you run either one of these what do you do if you want to press your AUX button and have the music stored on your USB drive attached in the left saddle bag to work?

You will be able to change to FM1, FM2, AM, and USB just like always.

[SeaSteve]

If anyone finds a simple Bluetooth TRANSMITTER that can be connected to the headset wire/connector, please let me know. I'm okay with leaving my phone plugged into the AUX 3.5 audio INPUT plug but would like to Bluetooth the OUTPUT to my helmet speaker system.

I should get the louder J&M Speakers in the mail this Friday, and installed Saturday, so I can hear music above 65MPH.

[shortleg0521]

If anyone finds a simple Bluetooth TRANSMITTER that can be connected to the headset wire/connector, please let me know. I'm okay with leaving my phone plugged into the AUX 3.5 audio INPUT plug but would like to Bluetooth the OUTPUT to my helmet speaker system.

I should get the louder J&M Speakers in the mail this Friday, and installed Saturday, so I can hear music above 65MPH.

All you need is an adapter that is 5 pin din on one end and 3.5 on the other.
Can be had for 10 to 15 bucks for a good one.
Then any Bluetooth transmitter will work.

[shortleg0521]

If anyone finds a simple Bluetooth TRANSMITTER that can be connected to the headset wire/connector, please let me know. I'm okay with leaving my phone plugged into the AUX 3.5 audio INPUT plug but would like to Bluetooth the OUTPUT to my helmet speaker system.

I should get the louder J&M Speakers in the mail this Friday, and installed Saturday, so I can hear music above 65MPH.

If you just want a good transmitter I use a sena sm 10.
IT NEEDS AN ADAPTER THAT GOES FROM 5 PIN DIN TO 3.5
It has two 3.5 plugs one for the headset jack and the other can be used for a gps that has a 3.5
Plug. If used it will over ride the music and give directions.
Have used one for quite a while and its worked great.

[2wheelsforme]

Just for info. If you are planning on adding a GPS unit soon be aware that some units have Bluetooth built in.

[Macs_F6B]

Just for info. If you are planning on adding a GPS unit soon be aware that some units have Bluetooth built in.

Thanks for the input.

So i'm thinking maybe of getting a Zumo GPS.

How exactly could this affect my decision here? What factors do i need to consider?

Thanks again!
-Mac

[shortleg0521]

Just look at what you want going on in your helmet.
When on a l9ng trip I enjoy listening to all kinds of music and even the news.
Sso I use XM radio in the left cubby and thumb drive in bag transmitted to
my Sena 20s headset by way of a sena sm 10.
Some of here don't listen to anything but the wind..
All in whatt you want.

[Switchmonkey]

08496E86-8277-459D-846B-B60405197E86.jpeg

I’ve got a Bluetooth receiver/transmitter plugged into the DIN jack. I use it so I can control everything from the bike controls and send it to my Sena 20S. TAO Tronics. It works great! I bought something from electrical connections thinking it would do the same but it is only a receiver. I cut the wiring and power the Tao tronics one using the connectors from the other one. It is always powered when bike key is on.