II Kings 9:20...and the driving is like the driving of Jehu the son of Nimshi; for he driveth furiously. A.K.J.V.
Bridgestone Potenza RFT 195/55-R16
BT45R 130/70-18
It happened last week on the eastbound I10.
I was somewhere in New Mexico, on my way to Texas to visit my daughter.
23Aug2019.jpg
Last edited by yabiah; 08-31-2019 at 09:31 AM.
I think everybody that turns 100K should provide a list of all maintenance done to date. Did anything actually break, or wear out? Did anybody require a valve adjustment? Anything other than normal consumables (tires, oil, brakes). Inquiring minds want to know what lies ahead....
DarkKnt,
Good question. My scoot is a 2013 and I bought it in April of 2014. With 140,467 on the clock here's the Repair List:
1). Alternator 8/24/16 @ 56,152 miles. It never quit, I was just blowing headlights what I thought was too often. Warranty
2). Fork seals 4/19/17 @ 67,514. One leaked which warranty paid for and I paid for the other. $412 and also included new fluid for both.
3). Steering Stem bearing 8/10/17 @ 83,489 All balls aftermarket installed $653 right after my first trip to Alaska. I was presented with the old steering stem race by my dealer. It was cracked and I now ride slower in Alaska.
4). 8/10/17 @ 83,489. Rear drive seal had a very light drip that started in Alaska. I never had to add oil. Warranty
5). Generator pulse 11/9/17 @ 92,101. An electrical part that caused the bike to cut off sometimes only while at idle. It would start right back up and run fine. Warranty
6). Front wheel bearings 2/17/18 @ 95,456 miles. The only way I knew they needed changing was my gas mileage dropped. I will change them every 75,000 miles from here out. I posted pictures on this forum of the old bearings and they were junked. So if you just joined the 100k club, my advice is to change your front wheel bearings. The bearings were $50? My son put them in.
7). Saddle bag plastic surrounding one hinge broke. 6/7/18 @ 102,980 miles. Warranty. Thanks Honda!
8). I know the right hand kill switch was replaced under warranty at some point. These need to be used on a regular basis.
9). Around 120,000 miles I replaced the clutch lever due to the wear it had. It had a little up and down motion and it bothered me. So I got an eBay unit that was like new for less than $75.
Note that my scoot has seen what most would consider severe service. Consistently rode hard and put up wet. At least 3 months of cumulative camping and it's likely over 4. In addition to the travel she had to live outside for a year. We have seen the lower 48, Alaska twice and every rideable Canadian Province except Labrador and Newfoundland. The F6BX has never failed to start or left me stranded. Within the last month my local Honda Service Manager has listened for valve noise and advised that I don't need a valve adjustment. It's never had one and never has been been checked any other way.
I have every gas receipt save 2. That's how I keep a check on the health of the bike. It's also a way to see where I've been. I know what the gas mileage should be based on what kind of riding I did that tank. I have not seen a decrease in performance yet. When I say this bike runs like new that's exactly how she runs. I will say the tone of the mufflers have deepened a tad. I'm very pleased with this marvelous machine!
I hope this helps and happy riding to you!
Last edited by Drive Jehu; 09-20-2019 at 08:16 PM. Reason: Posting wheel bearing photo
II Kings 9:20...and the driving is like the driving of Jehu the son of Nimshi; for he driveth furiously. A.K.J.V.
Bridgestone Potenza RFT 195/55-R16
BT45R 130/70-18
Thanks for that, exactly what I was hoping for... Some interesting stuff there. As an aside, I don't yet have 50K miles, but have changed both low beams 3 times each. Since the new alternator, how are bulbs lasting?
The only thing that I had to have done unexpectedly was the CPK sensor. I got the turn, turn, turn, no start and the Code 19. Then it started after a short waiting period.
I alerted my dealer (I was on the road) and they said bring it in. It worked fine the rest of the trip and when I brought it in, they "documented the failure" but didn't change it. When it started acting up again, I took it right to them and they changed it then. That time span was almost a year....lol.
Looking at Jehu's notes, I had the Traxxion Mega Monty installed so my fork seals, bearings etc were all redone as part of that install and have been maintained by Traxxion since.
I always use the Engine Cut Off switch (in both directions) so keep it exercised. See Phantom's post on what happens if you don't exercise it and only use the key.
I've never changed my wheel bearings, and Isleen hasn't seen the "hard mileage" that Jehu's F6BX has seen, but I'm gonna start paying attention there.
Great idea!
Cheers,
Steve
Hey Steve!
I think the wheel bearings being worn out had more to do with me not being careful with the hose and occasional pressure washer. I have ridden in a whole lot of rain. I've also ridden in a lot of calcium chloride slush. ( I hear the X corroding when it's real quiet). A few thousand miles of off road. Bad bumps. None of this helped the wheel bearings.
My best guess is the after adventure deep cleaning that involved water under pressure contributed the most. During those times often the bike would be layed down on each side. But I really don't know the cause for sure.
Also note that the traditional check of side to side play and spinning the wheel to listen gave no indication of a problem. It was only the gas mileage drop that started me on the hunt for a problem. I just posted a photo in my original post of the rusty bearings.
II Kings 9:20...and the driving is like the driving of Jehu the son of Nimshi; for he driveth furiously. A.K.J.V.
Bridgestone Potenza RFT 195/55-R16
BT45R 130/70-18